Easily Connect to Hioki Memory HiCorders and HiLoggers for High Voltage Testing
DIFFERENTIAL PROBE P9000
Model No. (Order Code)
|P9000-01||For the Memory HiCorder series, Wave only|
|P9000-02||For the Memory HiCorder series, Wave/RMS|
Note: Connect to a Memory HiCorder’s analog input terminal. Must be powered by an AC adapter, USB bus power, or other suitable power source.
•Compact probe for CAT III 1000V environments
•Use WAVE mode to observe instantaneous waveforms
•Use AC-RMS mode to observe RMS waveforms
1. High-voltage battery circuits in vehicles such as EVs and HEVs
2. High-voltage circuits in solar power installations and other alternative energy systems
3. Commercial power circuits, for example 480 Vrms circuits
4. High-voltage surge noise from inverters, motors, and solenoids, etc.
Basic specifications (Accuracy guaranteed for 1 year, Post-adjustment accuracy guaranteed for 1 year)
|Measurement functions||Waveform monitor output only
Frequency characteristics: DC to 100 kHz, -3 dB
|Waveform monitor output/AC RMS value output (switchable)
Wave mode frequency characteristics: DC to 100 kHz, -3 dB
RMS mode frequency characteristics: 30 Hz to 10 kHz; response time: 300 ms (rising) or 500 ms (falling)
|Division ratio||1000:1 or 100:1 (user selectable)|
|DC amplitude accuracy||±0.5% f.s. (f.s. = 1.0 V; voltage division ratio: 1000:1) (f.s. = 3.5 V; voltage division ratio: 100:1)|
|RMS amplitude accuracy||±1% f.s. (30 Hz to 1 kHz non-inclusive, sine wave), ±3% f.s. (1 kHz to 10 kHz, sine wave)|
|Input resistance, capacity||Between H and L: 10.5 MΩ, 5 pF or less (at 100 kHz)|
|Max. allowable input||1000 V AC/DC|
|Max. rated voltage to earth||1000 V AC/DC (CAT III)|
|Operating temperature||-40 ˚C (-40 ˚F) to 80 ˚C (176˚F)|
|Power supply||(1) AC Adapter Z1008 (100 to 240 V AC, 50/60 Hz), 6 VA (including AC adapter) or 0.9 VA (probe only), (2) USB bus power (5 V DC, USB Micro-B receptacle), 0.8 VA, (3) External power supply (2.7 V to 15 V DC)|
|Dimensions and mass||128 mm (5.04 in)W × 36 mm (1.42 in)H × 22 mm (0.87 in)D, 170 g (6.0 oz), Cord length: Input: 70 cm (2.30 ft) ; output: 1.5 m (4.92 ft)|
|Accessories||Instruction manual ×1, alligator clips ×2, carrying case ×1|
DIFFERENTIAL PROBE P9000
Differential Probe P9000-01/-02
Declaration of Conformity
DIFFERENTIAL PROBE P9000-01,P9000-02 [100KB]
Input cable (B)
*Voltage is limited to the specifications of the input modules in use.
GRABBER CLIP 9243
Input cable (D)
* Voltage to ground is within this product’s specifications, separate power source is also required.
AC ADAPTER Z1008
Input cable (F)
* Voltage input via banana terminals limited by the voltage specifications of the respective input unit.
MAGNETIC ADAPTER SET L4937
BUS BAR CLIP SET L4936
ALLIGATOR CLIP SET L4935
EXTENSION CABLE SET L4931
Input cable options
Test Pin Set L4932 is required when using the Small Alligator Clip Set L4934.
BREAKER PIN SET L4939
TEST PIN SET L4938
SMALL ALLIGATOR CLIP SET L4934
TEST PIN SET L4932
* Please contact your local HIOKI distributor for connectors that support Model MR8791.
CONVERSION CABLE L1011
CONVERSION CABLE L1011-10
There are no drivers, firmware or software available for this product.